Wilo EMU FA Sanitary Pumps

Wilo EMU FA Sanitary Pumps

Delivery on the territory of Ukraine: according to the delivery service rate
Customer pickup (ex-stock): free of charge
Payment: direct financial payment, bank transfer,
redelivery
Warranty: official manufacturerwarranty..

Submersible pump for wastewater disposal with a dry rotor motor 

Submersible sewage pump as submersible monobloc unit for stationary and portable wet well and dry well installation. Portable installation is possible, depending on type.
 

Type key
Hydraulics, for example:

Wilo‐EMU FA 08.34E
FA Submersible motor pump for wastewater
08 x10 = nominal diameter of pressure nipple, DN80 for example
34 Nominal power ratio
E Impeller type
   
Motor, for example:

Wilo-EMU T 17.2-4/24K Ex
T Motor construction material
17 Unit size
2 Reference number
4 Number of poles
24 x10 = burst length [mm]
K Seal construction material 
Ex Available
 
Technical data
  • Mains connection: 3~400 V, 50 Hz
  • Immersed operating mode: S1
  • Surfaced operating mode with self-cooling motor: S1
  • Protection class: IP 68
  • Max. fluid temperature: 3 ‐ 40 °C, higher temperatures on request
  • Sealing: With rotary shaft seal and mechanical seal, two mechanical seals or one block seal cartridge, depending on the motor
  • Free ball passage: 45 - 130 mm.
  • Permanently lubricated roller bearings
  • Max. immersion depth: 20 m
Operational Characteristics:

Operational Characteristics: EMU FA

Special features/product advantages
  • Operation in stationary and portable wet well and dry well installation
  • Submersible
  • Easy installation due to suspension unit or pump base
  • Special materials and coatings against abrasion and corrosion
  • Longitudinally watertight cable lead-in (depending on motor)
  • Adjustment of duty point by trimming the impeller

Application
  • Pumping of sewage with solid constituents in water treatment systems and pumping stations
  • Local drainage, water control and process water extraction
  • Applications in construction and industry
Hydraulics:

The outlet on the pressure side is designed as horizontal flange connection. The maximum possible dry matter content is 8%, depending on the hydraulics and impeller type.

The following impeller shapes are used:

  • Vortex impeller (W)
  • Single-channel impeller (E)
  • Two-channel impeller (Z)
  • Three-channel impeller (D)
The single and multi-channel hydraulics (Z, D) are equipped with a mobile and stationary wear ring (depending on type). These contribute long-term to ensuring the uniform efficiency of the unit.
 
Motor

Dry motors (T motors) give off their heat directly to the surrounding fluid via the housing components and can be used in immersed state for permanent operation. Depending on the size, they can also be used in non-immersed state for short-term or permanent operation.

The oil-filled motors (FK motors) and self-cooling dry motors (FKT, HC motors) give off their heat to the pumped fluid via a built-in heat exchanger. Therefore, these motors are suitable for permanent operation in immersed and non-immersed condition or for dry well installation.

All motors have a sealing chamber that protects the motor from fluid ingress. It can be accessed from the outside and can be monitored with an optional sealing chamber electrode.

All filling fluids used are potentially biodegradable and environmentally safe.

The cable inlet on T, HC and FKT motors is longitudinally watertight. Up to motor size 17, cable lengths are available in fixed lengths measured in 10 m intervals. Starting from motor size 20, the cable length can be individually configured.
 
Sealing
Fluid-side and motor-side sealing is possible in the following versions depending on the motor type:
  • Version H: Mechanical seal for the fluid side, rotary shaft seal for the motor side
  • Version G: Two independently operating mechanical seals
  • Version K: Block seal cartridge with two independently operating mechanical seals